Commercial Ice Machine Troubleshooting: Hoshizaki Beep Codes and Manitowoc Indigo NXT

Most ice machine calls are one of four things: no ice, slow or thin ice, ice that won't drop, or a freeze-up. Both big makers build a self-diagnosing control into their cubers, and the fastest way to the fault is to read what the board is telling you before you put gauges on.

This guide follows two manufacturer documents: Hoshizaki's service manual for its large modular KM crescent cubers (KM-901, KM-1100, KM-1340 and KM-1601 J series), and Manitowoc's Indigo NXT installation, operation and maintenance manual. Other Hoshizaki and Manitowoc models use the same ideas with their own numbers, so check the manual for the model on the data plate.

Hoshizaki KM: read the LEDs first

When the control switch goes to ICE, the board beeps and the red POWER LED comes on. Then the green LEDs light in order as the machine works through its cycle. Which green LED is lit tells you where the machine is, and the time limits tell you whether that step is taking too long.

On current boards (auxiliary code P-3 and later on the KM-901 and KM-1100, P-0 and later on the KM-1340 and KM-1601), the green LEDs are labelled for what they power:

Step Green LEDs on Normal time
1-minute fill WV (inlet water valve) 1 minute
Harvest Comp, WV, FM/HGV 1 to 20 minutes
Harvest pump time (harvest assist) Comp, PM, FM/HGV 0 to 50 seconds
Freeze Comp, PM 5 minutes to the freeze timer setting
Pump-out Comp, PM, FM/HGV, DV 10 to 20 seconds

Older boards (P-2 and earlier, N-3 and earlier) number the LEDs 1 to 4 instead. The fill shows LED 4, harvest 1, 4 and 2, and freeze LED 1 alone.

If a machine sits on the harvest LEDs for close to 20 minutes or the freeze LEDs for longer than normal, you already know which half of the cycle to work on.

Hoshizaki alarm beeps

Fix the cause, then press the ALARM RESET button with the power on.

Beeps Alarm What to check
1 High evaporator temperature (over 127°F) A harvest problem: stuck hot gas valve or relay, hot water entering the unit, a stuck headmaster (remote models), or a shorted thermistor.
2 Harvest backup timer: harvest over 20 minutes, two cycles in a row Open thermistor, hot gas valve not opening, TXV or liquid line valve leaking by, low charge, weak compressor, or the water regulating valve leaking by.
3 Freeze timer: freeze past the freeze timer setting, two cycles in a row Float switch stuck closed (up), inlet water valve or hot gas valve leaking by, pump not pumping, bad TXV, liquid line valve not opening, low charge, headmaster not bypassing, or a weak compressor.
Red POWER LED blinks Freeze-up detection (board 2A9678-02) The thermistor reached 2°C too fast after the freeze cycle started. Work through the freeze-up checklist below. Older 2A7664-02 boards blink for freeze-time correction instead.
6 Low voltage (92 VAC ±5% or less on the control circuit) The red LED goes out while voltage protection is active. Resets on its own when voltage recovers.
7 High voltage (147 VAC ±5% or more) Same: resets on its own when voltage is corrected.

Hoshizaki: no ice at all

Hoshizaki's diagnostic table runs top to bottom from the power supply. In short:

  • Power: breaker off, blown fuse, or voltage out of spec. On 208-230 V models with a main transformer, check the voltage tap switch.
  • Control box fuse blown.
  • Bin control: tripped with the bin full, or defective. Thermostatic bin controls also trip if the room is too cool, the setting is too warm, or the bulb has moved. Ultrasonic bin controls stop the machine when the sensor lens is dirty.
  • Control switch in OFF or WASH.
  • High-pressure switch open: dirty condenser, fan motor not running, overcharge, or a plugged line.
  • Control board: in alarm, or showing bin full (yellow BC OPEN LED on 2A7664 boards, orange BIN CLS LED on 2A9678 boards).
  • Water supply: shut off, low pressure, or clogged external filters.
  • Inlet water valve: clogged screen or orifice, or open coil.
  • Float switch stuck or defective.
  • Refrigeration and motors: compressor contactor, capacitors, start relay or internal protector; hot gas valve closed in harvest or open in freeze; liquid line valve closed in freeze or open in harvest; a loose TXV bulb; thermistor; pump motor or fan motor windings, bearings or capacitor; and water leaks that cut the freeze short.

Hoshizaki: freeze-ups

Hoshizaki's first instruction: melt off the ice and clean the icemaker before you diagnose a freeze-up, then fill out its freeze-up check list.

During the harvest cycle, look at a scaled or damaged evaporator, cube guides or spray tubes out of position or dirty, low water pressure, clogged filters or a water line smaller than 1/4 inch ID, a clogged inlet valve screen, a dirty or sticking float switch, low charge, the harvest timer (S4 dip switches 1 and 2) set too short, a dirty bin control, a loose or bad thermistor, a closed or restricted hot gas valve and an open liquid line valve.

During the freeze cycle, a freeze-up usually traces to:

  • A scaled or damaged evaporator, or dirty or misplaced spray tubes and guides.
  • Low refrigerant charge.
  • The freeze timer (S4 dip switches 9 and 10) set wrong.
  • The inlet water valve leaking by.
  • The float switch sticking.
  • A slow pump or damaged impeller.
  • A loose or bad TXV bulb, a restricted liquid line valve, or (remote models) a headmaster that isn't bypassing.

Manitowoc Indigo NXT: service faults

Besides the normal safeties like the high pressure cutout, Indigo NXT machines have built-in service faults that stop the machine before a major component fails. Manitowoc's restart procedure:

  1. Press the power button. The display reads "Off". Press it again and it reads "Making Ice".
  2. If a service fault stopped the machine, it restarts after a short delay. Let it run.
  3. If it stops again, the condition has repeated and needs a repair. If it keeps running, the condition cleared itself.

If it doesn't restart at all, start with the basics: power to the ice machine and condensing unit, the high pressure cutout (clean the condenser), Energy Saver or other programming stopping it, the water curtain off or stuck open, and on IB dispenser models, the dispenser ice level thermostat.

Manitowoc: won't harvest, slow harvest, bad ice

Problem Check
Won't release ice, or slow to harvest Dirty machine (clean and sanitize), machine not level, air around the head section below 35°F, fan cycle control not cutting off the condenser fan, water regulating valve not closing (water at the condenser drain during harvest).
Won't go into harvest The six-minute freeze lock-in hasn't expired; ice thickness probe dirty, disconnected or out of adjustment; uneven fill, thin at the top of the evaporator (low water in the trough or a refrigeration problem).
Soft or cloudy ice Poor water quality, bad filter, dirty machine, water dump valve not working, water softener problem.
Shallow or incomplete cubes Ice thickness probe out of adjustment, trough water level too low (check the water level probe), dirty inlet valve screen, poor filtration, hot incoming water, inlet valve not working, water pressure outside 20 to 80 psi, machine not level.
Low capacity Dirty inlet valve screen, water shut off, inlet valve stuck open or leaking, dirty condenser, hot air at the condenser, harvest assist air compressor not working.

Setting the ice thickness probe

The probe is factory-set for an ice bridge about 1/8 inch (3 mm) thick, the web of ice joining the cubes. To reset it, put a 9/32-inch (7 mm) drill bit between the probe and the evaporator to set the starting gap, run a cycle, and check the bridge. Clockwise on the adjusting screw makes the bridge thicker. A third of a turn changes it by about 1/16 inch. Keep the water curtain in place while you check, and make sure the probe wire doesn't hold the probe back.

Manitowoc also lists a minimum and maximum slab weight per cycle for each model, from 2.40 to 2.80 lb on an IF0300 up to 15.50 to 16.75 lb on an IF2100. Weighing a slab is a quick check of whether a "low production" complaint is real.

Cleaning schedules

A dirty machine shows up as slow harvest, cloudy ice, freeze-ups and alarms on both brands.

  • Manitowoc: clean and sanitize at least every six months, with the machine and bin taken apart, using only Manitowoc's approved cleaner and sanitizer. Never mix the two. Discard all ice made during cleaning. Clean the air filter and condenser too.
  • Hoshizaki: wash air filters every two weeks if dirty; check external water filters and the bin control lens monthly; and once a year clean and sanitize the machine and bin, clean the water supply inlet screen, clean the condenser and inspect the water hoses. Hard water or a dusty kitchen means doing it more often.

Common mistakes

  • Resetting a Hoshizaki alarm without reading it. The beep count is the diagnosis. Write it down before pressing ALARM RESET.
  • Chasing refrigeration on a dirty machine. Scale on the evaporator causes slow harvest and freeze-ups that look like a charge problem. Clean first.
  • Ignoring the bin control. A dirty ultrasonic lens or a tripped bin control looks exactly like "no ice."
  • Using the wrong chemicals. Manitowoc approves only its own ice machine cleaner and sanitizer, and warns that mixing them, or using them other than as labelled, violates federal law.
  • Low water pressure. Below 20 psi on a Manitowoc means short fills and thin ice, and no refrigeration repair will fix it.

FAQ

What does 3 beeps mean on a Hoshizaki ice machine?

On a KM crescent cuber, 3 beeps is the freeze timer alarm: the freeze cycle ran longer than the freeze timer setting two cycles in a row. Check the float switch, the inlet water valve and hot gas valve for leaking by, and the pump, then the refrigeration side.

How do I reset a Hoshizaki ice machine alarm?

Fix the cause, then press the ALARM RESET button with the power on. Low and high voltage alarms (6 and 7 beeps) reset on their own when the voltage is corrected.

Why won't my Manitowoc ice machine harvest?

It may still be inside the six-minute freeze lock-in. After that, the usual causes are a dirty, disconnected or misadjusted ice thickness probe, or a low water level in the trough giving a thin fill at the top of the evaporator.

How often should a commercial ice machine be cleaned?

Manitowoc calls for a full clean and sanitize at least every six months. Hoshizaki lists a yearly clean and sanitize plus monthly and biweekly filter and lens checks. Both say to clean more often with poor water or a dirty environment.

Sources

Related guides

Field reference for trained technicians. Always follow the equipment manufacturer's instructions, local code and safe work practices. See our editorial standards, or report a correction.