Boiler Circulator Not Running: Power, Relay, Seized Cartridge or Air Lock?
When a hot-water system has heat at the boiler but none in the house, the circulator is one of the first things to check. The question is whether it's being told to run, whether it can run, and whether it's actually moving water.
Safety: Circulators run on 120 V. Shut off power before opening the terminal box. Let the system cool and reduce pressure to 0 psi before removing a motor or cartridge; Taco's instructions say to isolate the circulator with its service valves or drain the system first. This is work for a trained technician.
Step 1: Is the circulator being told to run?
With a call for heat, measure voltage at the circulator's leads.
- No voltage: the circulator is fine for now. Follow the call back: thermostat, zone valve end switch, then the boiler's aquastat or a switching relay. See zone valve troubleshooting.
- Voltage present: go on.
Step 2: Is it turning?
Feel the motor body: a running circulator has a slight vibration and gets warm. A hot, silent motor with voltage on it has a locked rotor or a failed motor.
On standard Taco "00" cartridge circulators (such as the 007), the motor and cartridge come apart from the pump body. Taco's procedure: disconnect power, reduce system pressure to 0 psi and let it cool, isolate the circulator, remove the body bolts, swing the motor away, and pull the cartridge. Install a replacement cartridge matching the full circulator product number, with the cover plate between the cartridge flange and the motor, and reassemble with the new gasket and bolts supplied.
Taco's 00e ECM circulators have a "SureStart" feature: on a locked rotor they rapidly vibrate to try to free it. On the VR1816, Taco says the pump makes 100 restart attempts over about 15 minutes, each signaled by a short white LED flash; if that fails it goes to standby with a solid red LED, and the instructions list manual unblocking steps.
Step 3: Running, but no heat downstream?
- Air in the pump or loop. Taco says to operate the circulator for 5 minutes right after filling to purge air from the bearing chamber, especially when starting it in the off-season. Purge the zones one at a time using the purge valves.
- Closed valves. Check isolation valves on both sides of the pump, and the zone valve.
- Flow check stuck. Many "00" circulators have an integral flow check (IFC) in the discharge. A stuck one blocks flow. Taco's instructions show how to remove and replace it.
- Low system pressure. Taco notes a circulator may be mounted vertically with the motor up only if system pressure is at least 20 psi; low pressure invites air problems.
Installation details that cause trouble
From Taco's instruction sheets:
- Mount the circulator with the motor horizontal, or vertically with the motor up only at 20 psi or more.
- Don't put the junction box at the 6 o'clock position under the pump.
- Use the O-ring gaskets supplied, not flat rubber gaskets.
- Never run the circulator dry; the bearings are water lubricated.
- Taco recommends pumping away from the expansion tank, with the circulator on the supply side.
Common mistakes
- Condemning the pump when it never got power.
- Replacing the whole circulator when only the cartridge is seized.
- Starting a pump on an empty system. Dry running damages the bearings.
- Skipping the purge after a repair, then calling the new pump bad.
FAQ
Why does my boiler circulator hum but not pump?
Usually a stuck rotor or a failing motor. Confirm it has power, then check whether the cartridge turns freely with the power off and the pump isolated.
Can I replace just the cartridge on a Taco 007?
Yes, on "00" cartridge circulators the cartridge is replaceable. Match the replacement to the full product number on the circulator.
Where should the circulator be?
Taco recommends the supply side of the boiler, pumping away from the expansion tank.
Sources
- Taco "00" Cartridge Circulators instruction sheet 102-054
- Taco 0012 & 0013 Multi-Speed Cartridge Circulator instruction sheet 102-485
- Taco 00e VR1816 instruction sheet 102-499
- Taco 00e VT2218 instruction sheet 102-525
HVAC Cheat Sheet is published by 90 Leads, a marketing company that works with home service businesses, including HVAC contractors.
Was this guide useful?
One field tip a week
A short, practical HVAC tip in your inbox every week: diagnostics, charging, airflow and code changes. Free, unsubscribe anytime.
We'll only use your email for the newsletter. Privacy policy.
Related guides
Air in a Hot-Water Heating System: Purging, Air Separators and Vents
Why air causes no-heat zones, noise and pump problems in a hot-water heating system, how to purge bulk air with forced-water purging (and the flow you need), and where the air separator, expansion tank and vents belong. Based on Taco's technical documents.
Hot-Water Zone Valve Troubleshooting: Valve, Motor or End Switch?
How to find out why a hydronic zone gets no heat or won't shut off. Covers how a zone valve and its end switch start the boiler, what to measure, and how to tell a bad motor head from a stuck valve.
Boiler Short Cycling: Settings, Flow, Venting or an Oversized Boiler?
A checklist for a hot-water boiler that fires, shuts off and fires again every few minutes, based on IBC's cycling troubleshooting table for its condensing boilers. Covers control settings and differential, low water flow, air, venting and condensate, and boiler size.
Furnace Gas Valve Not Opening: Igniter Glows but No Flame
How to tell whether a furnace that glows or sparks but never lights has a bad gas valve, a board that isn't sending 24 volts, a closed gas supply or a pressure problem, with the checks in order.
Field reference for trained technicians. Always follow the equipment manufacturer's instructions, local code and safe work practices. See our editorial standards, or report a correction.